Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - RCinLaveen

Pages: [1] 2 3
1
What are you riding? / Re: My favorite ride!
« on: May 28, 2019, 08:38:58 PM »
May be headed up to Prescott this weekend.  Will post up details.  Anyone up for a ride?

2
What are you riding? / Re: My favorite ride!
« on: May 28, 2019, 06:15:35 AM »
Well, there ya go!

3
What are you riding? / Re: My favorite ride!
« on: May 26, 2019, 07:50:52 AM »
How many folks on here ride?  I've got an Ultra.  We should get a group together and ride one weekend.

4
General Discussion / Re: I'm back *****!!!
« on: May 06, 2019, 08:03:53 PM »
Looks like a great pallet with which to start. 

5
Builds / Re: JYD's new rig build
« on: March 19, 2019, 08:20:32 AM »
Looking good

6
General Discussion / Re: IF I HAD MONEY I WOULD DO THIS TO MY RIG!
« on: December 21, 2018, 01:59:23 PM »
I'm pretty much of the same opinion, but at this point....

7
General Discussion / Re: IF I HAD MONEY I WOULD DO THIS TO MY RIG!
« on: December 21, 2018, 10:50:33 AM »
I'd pay a good fab shop to finish it.

8
Builds / Re: Big Little Buggy Build
« on: November 27, 2018, 10:54:33 AM »
The buggy turned out very nice.

9
Trail Runs / Re: 9th Annual Florence Fest
« on: November 09, 2018, 03:23:59 PM »
You all have fun.  My rig is getting close, but still not done.  Post some pics and videos!

10
Builds / Re: Big Little Buggy Build
« on: August 31, 2018, 10:24:14 AM »
Nice.  Look forward to following the build.

11
Builds / Re: Race Heep
« on: January 11, 2018, 08:07:14 PM »
All that Artec and Ruff Stuff Specialties "stuff" is much nicer looking than "Bob's hillbilly garage" stuff.  :clap:

12
Toyota / Re: 2012 Tundra - CEL and gas mileage reduction
« on: December 19, 2017, 08:19:55 AM »
Go to Auto Zone, etc., and have them pull the codes for free. That will point you in the right direction as far as needed service or parts replacement.

13
Builds / Re: Race Heep
« on: November 10, 2017, 10:34:45 AM »
If the background wasn't there for context, that looks like a lot of Jeeps in and around NY city!

Looking forward to seeing this one finished.

got the fuel tank dropped and cleaned up the back half of the chassis. Also managed to get the front axle out and started clean up. We should be able to start welding and bending tube in the next couple weeks!





14
Builds / Re: tha' 82
« on: October 06, 2017, 02:07:59 PM »
Cool, Eryc.  I'll be mocking up some triangulation for the front four link this weekend.

15
Builds / Re: Race Heep
« on: September 06, 2017, 12:17:41 PM »
nice looking pile of parts - looking forward to following the build

16
Builds / Re: tha' 82
« on: July 19, 2017, 06:43:09 PM »
I've got most of the parts for the full hydro conversion now, and I have a question about the stub shaft that attaches to the hydro valve.  I expected it to have splines, but it doesn't.  From the pic's, looks like yours doesn't either - the u-joint slips over, and it's all held in place by a set screw?

17
General Discussion / Re: How High Did You Get
« on: June 20, 2017, 07:55:33 PM »
127 today in Laveen.  But, low humidity made it "feel" like it was only 122 - so it's all "cool." 

18
General Discussion / Re: How High Did You Get
« on: June 19, 2017, 07:21:50 PM »
According to Weather Underground, officially 123 degrees today at the house,  Laveen.  We'll be cooling off tonight though, down to 85.

19
Builds / Re: tha' 82
« on: June 05, 2017, 01:06:20 PM »
Very nice.  Looks a lot different without the leaf springs on there.  If you're heading North, I'll tag along.  I've done nothing to my rig yet - still waiting to hear from the IRS, post appeal.  I "won" half of what they said I owed, and now I'm waiting on word on the other half.   They're taking their sweet time to let me know about their latest decision, but I'm sure I'll win that appeal too, if I don't, back to the drawing board.  Just don't want to owe the govt. and the buggy at the same time  :shakehead:

20
Builds / Re: tha' 82
« on: May 22, 2017, 02:49:16 PM »
Looks good to me so far.  Between work, travel, family visits and waiting for the right parts - I spent a year just putting tons under my  truck.  You've made good time. 

I'm afraid to take the front of the rig apart for the 4 link project.  The only motivation is I've already done the rear, so I have some experience and expectations.  I bet I'll do what I've always done though, I think I'll get it done quickly and end up taking four times as long as I should.

21
Truggy/Buggy / Re: Which is stronger output for tcase 1410 or flange?
« on: April 19, 2017, 09:28:57 PM »
Angles aside, a 1410 allows for more flex....larger, more.  But a 1410 is uber tough.

22
Builds / Re: tha' 82
« on: April 17, 2017, 10:00:20 PM »
Tough part, springs aren't the only part of the equation.  Vehicle weight, and valving?  That's all I know.  I run junk yard coils...

Never heard of hardening link material after welding either, I'm feeling uninformed.  I have some more to learn.

23
Builds / Re: tha' 82
« on: April 17, 2017, 12:08:51 PM »
Nice progress, Eryc.

24
Builds / Re: tha' 82
« on: April 02, 2017, 10:23:22 AM »
Very nice

25
Trail Runs / Re: TAble Mesa weekend
« on: December 23, 2016, 10:20:57 PM »
I'll be there.

Pages: [1] 2 3

SimplePortal 2.3.3 © 2008-2010, SimplePortal