Author Topic: The Beast 2.0?  (Read 427 times)

Cuda K5

  • Hero Member
  • *****
  • Location: Wittmann
  • Join Date: Mar 2010
  • Posts: 2062
  • Cocked-N-Locked Fab
    • View Profile
    • Cocked-N-Locked Fab
The Beast 2.0?
« on: September 16, 2018, 09:10:33 PM »
Drug home project #3...........I may have a problem, but I couldn't pass up this opportunity

This rig is going to get thrown together fast with almost no money into it. Hoping to trail wheel it before the end of the year

Below is all of the parts we already have laying around

350 crate motor with Holley Fuel Injection
TH400 (needs rebuild)
NP203/205 doubler (needs adapter to trans)
Dana 60 front w/4.56 gears and locker, chromalloy shafts, PSC Hydro Assist
Shaved 14bff (came with the truck) I already have a line on a 4.56 14 bolt (needs disc brakes and ring turned down)
Suspension is all staying original. I just need to change out one of the front main leafs
We have a whole wiring harness set up for the 350 we will swap into this rig
I still have the old smittybuilt winch from my blazer
Going to add a few more supporting tubes to the roll cage. I have all of the tubing laying around the house.

Need to find seats and buy seat belts, but we might just use the Jeep seats until we find something cheap.
All of the plumbing will need to be done
Need a shifter for the trans
Also need to find a set of tires and wheels which will be where most of the money for the build goes.



Cocked-N-Locked Fabrication and Racing

www.cockednlockedfab.com

Facebook @cockednlocked
Instagram @cocked_n_locked_racing
Youtube @ Cocked-N-Locked Racing

ROCKZILLA

  • Administrator
  • Hero Member
  • *****
  • Location: Maricopa
  • Join Date: Mar 2010
  • Posts: 2547
    • View Profile
Re: The Beast 2.0?
« Reply #1 on: September 18, 2018, 06:09:20 AM »
Hurry up...you’re closer than me!
It started life as a 1987 Samurai and turned into a Psychobilly Cadillac .

Cuda K5

  • Hero Member
  • *****
  • Location: Wittmann
  • Join Date: Mar 2010
  • Posts: 2062
  • Cocked-N-Locked Fab
    • View Profile
    • Cocked-N-Locked Fab
Re: The Beast 2.0?
« Reply #2 on: September 18, 2018, 11:27:29 AM »
I think we just found some old 37"s that I'm going to run for now. Just need some wheels
Cocked-N-Locked Fabrication and Racing

www.cockednlockedfab.com

Facebook @cockednlocked
Instagram @cocked_n_locked_racing
Youtube @ Cocked-N-Locked Racing

Cuda K5

  • Hero Member
  • *****
  • Location: Wittmann
  • Join Date: Mar 2010
  • Posts: 2062
  • Cocked-N-Locked Fab
    • View Profile
    • Cocked-N-Locked Fab
Re: The Beast 2.0?
« Reply #3 on: January 05, 2019, 08:13:41 PM »
Got Optimus Primer's engine, trans, and doubler out. Engine is on the stand getting ready for a new PSC pump, manifolds, flexplate and a few other odds and ends that broke or failed. Luckily we have a TH400 in the shed already set up for a np203, so I just ordered an adapter. I will take the trans down to Sun Transmission this week to get a reverse manual valve body, stock rebuild, and new torque converter. Hoping to get the D60 out from under it next weekend and into the beast





Cocked-N-Locked Fabrication and Racing

www.cockednlockedfab.com

Facebook @cockednlocked
Instagram @cocked_n_locked_racing
Youtube @ Cocked-N-Locked Racing

ROCKZILLA

  • Administrator
  • Hero Member
  • *****
  • Location: Maricopa
  • Join Date: Mar 2010
  • Posts: 2547
    • View Profile
Re: The Beast 2.0?
« Reply #4 on: January 06, 2019, 01:26:18 PM »
 :clap:
It started life as a 1987 Samurai and turned into a Psychobilly Cadillac .

JYD

  • Administrator
  • Hero Member
  • *****
  • Location:
  • Join Date: Mar 2010
  • Posts: 1546
  • f*** it! lets go wheeling!!
    • View Profile
    • ALLOFFROADAZ.COM
Re: The Beast 2.0?
« Reply #5 on: January 07, 2019, 04:37:25 PM »
Better hurry up your going to miss KOH

Cuda K5

  • Hero Member
  • *****
  • Location: Wittmann
  • Join Date: Mar 2010
  • Posts: 2062
  • Cocked-N-Locked Fab
    • View Profile
    • Cocked-N-Locked Fab
Re: The Beast 2.0?
« Reply #6 on: January 07, 2019, 04:53:11 PM »
We aren't bringing anything for KOH. Just going to be there to help in the pits.

I do needs this running and driving soon though. I have to get the jeep rolling before it gets hot outside
Cocked-N-Locked Fabrication and Racing

www.cockednlockedfab.com

Facebook @cockednlocked
Instagram @cocked_n_locked_racing
Youtube @ Cocked-N-Locked Racing

Cuda K5

  • Hero Member
  • *****
  • Location: Wittmann
  • Join Date: Mar 2010
  • Posts: 2062
  • Cocked-N-Locked Fab
    • View Profile
    • Cocked-N-Locked Fab
Re: The Beast 2.0?
« Reply #7 on: January 20, 2019, 09:51:51 PM »
Engine is cleaned up. Installed new manifolds and PSC pump. We had to play musical vehicles and tires to get the blazer in the right position for the axle swap. Mounted all 4 bald treps and picked up all of the brake parts needed for rear discs. We are going to use a pair of almost new 2.5" lift springs for the front that were laying around. I just need to stop at Copperstate tomorrow for new pins and the front axles will get swapped sometime this week.





Cocked-N-Locked Fabrication and Racing

www.cockednlockedfab.com

Facebook @cockednlocked
Instagram @cocked_n_locked_racing
Youtube @ Cocked-N-Locked Racing

 


SimplePortal 2.3.3 © 2008-2010, SimplePortal